Industrial Refrigeration Services Okanagan: Cold Storage, Food Processing and Agriculture

Industrial refrigeration services Okanagan plant managers, packers and growers rely on are a different job from keeping a restaurant walk-in cold. The equipment is bigger, the loads swing hard with the harvest, and a few hours of downtime can put a whole season of product at risk. This guide explains what industrial refrigeration covers, how maintenance differs from restaurant work, and what my team suggests checking before processing season gets busy.

What industrial refrigeration services Okanagan facilities cover
Industrial work is a step up in scale from a kitchen walk-in. In the Okanagan it typically means:
Cold storage rooms and warehouses that hold fruit, produce or packaged food at a steady temperature for weeks or months.
Process cooling, such as glycol chillers that pull heat out of fermentation tanks, brite tanks and processing lines at wineries and breweries.
Blast or rapid cooling that brings freshly picked or freshly processed product down to a safe temperature quickly.
Controls and remote monitoring that track temperatures across the whole facility and alert someone when a room drifts.
Our refrigeration services page lists the systems we install, repair and maintain, from walk-in coolers and freezers to cold storage and glycol chillers.
How industrial work differs from restaurant work
A restaurant cooler fails and the kitchen loses a shelf of product. A cold storage room fails during harvest and a packer may lose a truckload. That difference shapes how industrial refrigeration services Okanagan facilities depend on are planned and delivered.
Loads change with the season. A storage room that sits half empty in spring is packed to the ceiling in September, and the system has to handle both.
Pull-down matters. Fruit coming in from the field carries heat, and the system has to remove it quickly without freezing product near the coils.
Humidity matters as much as temperature for many crops, so controls and defrost settings need careful attention.
The cost of a surprise is higher, which makes planned maintenance and monitoring a bigger part of the picture.
Checks to make before processing season
As a general rule, the best time to find a problem is before the first bins arrive. These are the checks my team suggests scheduling in late summer or early fall, and again before any long storage period.
Run every room and chiller at its working setpoint for a full day and confirm it holds temperature with the doors closed.
Walk the outdoor condensing units and make sure they have clear airflow, with no leaves, debris or stored material against them.
Check door seals, strip curtains and closers on every cold room. Warm air leaking in is the most common reason a room struggles.
Confirm that defrost cycles are completing and that drains are clear, so meltwater does not refreeze on the floor or the coil.
Test alarms and remote monitoring. Make sure the right person gets the alert and knows what to do with it.
Review last season's log sheets for rooms that drifted or ran constantly, and have a technician look at those first.
Staff can safely do the visual checks, the door checks and the alarm tests. Anything involving refrigerant, electrical panels or the inside of a condensing unit should be left to a certified technician.
Cold storage after the harvest
Once product is in storage, the goal shifts from pull-down to stability. Steady temperature and humidity and good air circulation around the stacks help product hold its quality. If you are planning new or expanded storage, our post on high-capacity cold storage for the Okanagan harvest covers the planning questions in more detail.
Cold food should be held at 4 C (40 F) or colder, and perishable food should not spend more than about two hours between 4 C and 60 C. Your health authority or food safety advisor is the right source for the specific requirements that apply to your product.
Controls and remote monitoring
For a facility with many rooms, the control system is often where the biggest difference is made. Modern controls let you watch temperatures from a phone, and remote monitoring can send an alert when a room drifts in the middle of the night. We cover what these systems do on our advanced controls page. They do not replace maintenance, but they give you warning while there is still time to act.
When to call a technician
Call for industrial refrigeration services Okanagan technicians can respond to quickly if you notice any of the following:
A room or chiller that cannot reach or hold its setpoint.
Compressors that run constantly, short-cycle or trip breakers.
Heavy frost or ice on evaporator coils, or water where it should not be.
Unusual noise, vibration or oil around the equipment.
Custom Climates is a locally owned refrigeration and HVAC company based in Kelowna, with Red Seal Journeyman technicians and 24/7/365 emergency service across Kelowna, West Kelowna, Penticton, Vernon, Oliver and Osoyoos.
Industrial refrigeration FAQ
What counts as industrial refrigeration?
Industrial refrigeration generally means large-scale systems such as cold storage rooms, process chillers, blast coolers and rack systems that serve a plant or warehouse. It differs from commercial refrigeration mainly in scale, run time and the cost of a failure. Many Okanagan facilities use a mix of both.
How often should an industrial system be serviced?
There is no single answer, because it depends on how hard the system runs and how long the season is. Many operators schedule a thorough inspection before their busy season and a follow-up after it. A technician who knows your equipment can suggest a schedule that fits.
Can my own staff do any of the maintenance?
Yes, within limits. Staff can check temperatures, inspect door seals, keep airflow clear around units and test alarms. Refrigerant work, electrical work and anything inside a condensing unit should be left to a certified technician.
What should I do if a cold room starts to warm up?
Keep the doors closed, confirm the alarm is real with a trusted thermometer, and call for service right away. Do not try to add refrigerant, open electrical panels or chip ice off a coil. If product is at risk, start planning where it could be moved while help is on the way.
Do you serve wineries and breweries as well as packers?
Yes. Our clients include wineries, breweries, restaurants, supermarkets and agricultural operations across the Okanagan. Glycol chillers for fermentation and tank cooling are a regular part of our work.
Does remote monitoring replace a maintenance program?
No. Monitoring tells you when a room is drifting so you can act sooner, but it does not fix worn parts or dirty coils. The two work best together, with monitoring catching problems early and planned maintenance keeping them from starting.
Need help now? Call 250 869-5308 or request service online.
Jesse Tanner, Owner, Custom Climates






Comments